一二三四区视频,亚洲少妇熟女色,日本久热无码视频网,欧美国产日韩大尺度,亚洲a视频,久久少妇一区二区,日韩999无码视频,刺激久久久久久久,啊啊啊啊不要啊在线

Welcome to chemicalbook!
Chinese English Japanese Germany Korea
010-86108875
Try our best to find the right business for you.
Do not miss inquiry messages Please log in to view all inquiry messages.

Welcome back!

ChemicalBook CAS DataBase List Acrylic acid
79-10-7

Acrylic acid synthesis

14synthesis methods
There are three routes to acrylic acid which have commercial significance; they are based on propylene, acetylene and ethylene respectively. At the present time, most acrylic acid is produced via the propylene route.
(i) Propylene route. This route involves the two-stage oxidation of propylene:


A mixture of propylene, air and steam is fed into a reactor containing a catalyst at about 320°C to give acrolein. This intermediate is not isolated but is passed directly to a second reactor, also containing a catalyst, at about 280°C. The effluent is cooled by contact with cold aqueous acrylic acid.
Acrylic acid is extracted from the solution with a solvent and then separated by distillation. Because of the ready availability of low cost propylene, this route has become the preferred route for the production of acrylic acid. (ii) Acetylene route. This route involves the reaction of acetylene, carbon monoxide and water:


In one process, the reaction is conducted in solution in tetrahydrofuran at about 200°C and 6-20 MPa (60--200 atmospheres). Nickel bromide is used as catalyst. The solution of acrylic acid in tetrahydrofuran, after separation of the unconverted acetylene and carbon monoxide in a degassing column, passes to a distillation tower where tetrahydrofuran is taken overhead and acrylic acid is the bottom product. The reaction between acetylene, carbon monoxide and water may also be carried out by using nickel carbonyl as the source of carbon monoxide. In this case, milder reaction conditions are possible. Owing to the high cost of acetylene, this route is now of little commercial importance.
(iii) Ethylene route. This route consists of the following sequence:


The addition of hydrogen cyanide to ethylene oxide takes place at 55-60°C in the presence of a basic catalyst such as diethylamine. The reaction is exothermic and is carried out in solution to facilitate control; the solvent is conveniently ethylene cyanohydrin. The reaction mixture is neutralized and ethylene cyanohydrin is separated by distillation. The second stage of the synthesis involves the dehydration and hydrolysis of ethylene cyanohydrin; these reactions are carried out in one step by heating the cyanohydrin with aqueous sulphuric acid at about 175°C. (It is possible, of course, that the intermediate in this conversion may be acrylonitrile, as shown, or P-hydroxypropionic acid or both.) At one time this was the standard route for the preparation of acrylic acid but it has been largely displaced by the more economical propylene route.
-

Yield:79-10-7 99.9%

Reaction Conditions:

with water;sodium hydroxide in hexan-1-ol at 80; for 10 h;Sealed tube;Temperature;

Steps:

1 Example 1

0.75mmol of glyceric acid was sequentially added to a 50mL high temperature and high pressure reactor.100μmol PdCl2, 10ml 57wt% hydriodic acid, sealed reaction kettle,Fill with hydrogen (3000 psi), stir and heat to 170 ° C quickly.Hold for 25h. The reaction kettle ice water bath was cooled to room temperature, the aqueous phase was collected and tested.Glyceric acid conversion rate is 100%,The yield of 3-iodopropionic acid was 99.9% (about 0.75 mmol).Take 5 ml of the aqueous phase reactant and add 10 ml of n-hexanol to extract 3-iodopropionic acid.Extract three times and combine the extractants.Take 10ml of extract (containing about 0.125mmol of 3-iodopropionic acid)Add 10ml of water to a 50mL thick-walled glass tube.And adding 0.083g of sodium hydroxide to seal the reaction kettle.Stir and heat quickly to 80 ° C for 10 h.The reaction kettle was cooled to room temperature in an ice water bath, and the aqueous phase was collected, acidified and detected.The yield of acrylic acid was 99.9% (about 0.125 mmol).

References:

CN108997108,2018,A Location in patent:Paragraph 0020; 0021; 0031; 0033; 0035; 0037; 0039; 0041

Acrylic acid Related Search:

濉溪县| 贵港市| 万荣县| 无锡市| 德昌县| 临沂市| 临清市| 长治市| 龙州县| 普兰店市| 博兴县| 塔城市| 洱源县| 响水县| 南康市| 土默特右旗| 金阳县| 清徐县| 夏津县| 湖南省| 弥勒县| 乌兰县| 营口市| 大洼县| 吴桥县| 滦平县| 大化| 黄大仙区| 汪清县| 武义县| 柳林县| 郯城县| 綦江县| 福建省| 海盐县| 德惠市| 承德县| 泾阳县| 丘北县| 九江市| 双鸭山市|